2014 dodge journey key battery replacement

Dodge Journey Key Fob Battery Replacement Guide How to change the battery in the key fob remote control of a first generation 2009 to 2014 Dodge Journey SUV.

Copyright 2024 � PaulsTravelPictures.com  All Rights Reserved �

Privacy Policy      About Paul & Author Contact Info

Power Up: Replace Your Key Fob Battery Today

Dodge Journey Key Fob Battery Replacement Guide (2011 – 2021)

Introduction

Replacing the battery in your Dodge Journey key fob is a straightforward process. If your key fob has stopped working, it might just need a new battery. In this guide, I will show you how to replace the battery in a few simple steps.

Tools and Materials Needed

Before starting, gather the necessary tools and materials:

• CR2032 Coin Battery
• Flathead Screwdriver

You can purchase the CR2032 battery online. Here’s a link to buy the batteries: Buy CR2032 Battery .

Step-by-Step Instructions

Follow these steps to replace the battery in your Dodge Journey key fob:

Step 1: Remove the Internal Key

First, flip the key fob over. You will see a small switch. Pull this switch down, and the internal key will come out. Set the key aside for now.

Step 2: Locate the Keyhole and Slot

Once the key is removed, you will see the keyhole. Opposite the keyhole, there is a small slot or indentation. This is where you will insert your flathead screwdriver.

Step 3: Open the Key Fob

Insert the flathead screwdriver into the slot. Gently twist the screwdriver until you feel a snap. This indicates that the key fob is starting to open.

Continue twisting and working your way down the seam of the key fob until it comes apart completely.

Step 4: Remove the Old Battery

Once the key fob is open, you will see the battery. Use your flathead screwdriver or fingernail to lift the battery out. The battery should pop out easily.

Step 5: Insert the New Battery

Take the new CR2032 battery. Ensure the positive side (marked with a plus sign) is facing down. Click the battery into place.

Step 6: Reassemble the Key Fob

Now, align the two halves of the key fob and press them together. It may take some effort, but squeeze until the seam is closed completely.

Step 7: Replace the Internal Key

Finally, slide the internal key back into its slot. Your key fob is now ready to use with a new battery.

Replacing the battery in your Dodge Journey key fob is a quick and easy process. With just a few tools and a new battery, you can have your key fob working like new. If you found this guide helpful, feel free to share it with others.

What type of battery does the Dodge Journey key fob use?

The Dodge Journey key fob uses a CR2032 coin battery.

Where can I buy a CR2032 battery?

You can buy a CR2032 battery online or at most electronics stores. Here’s a link to purchase it on Amazon: Buy CR2032 Battery .

Do I need any special tools to replace the battery?

You only need a flathead screwdriver to replace the battery in the key fob.

How often should I replace the battery in my key fob?

Key fob batteries typically last 1-2 years. Replace the battery when the key fob stops working or the signal weakens.

Can I use a different type of battery?

It is recommended to use a CR2032 battery, as other types may not fit or function properly.

What if my key fob still doesn’t work after replacing the battery?

If your key fob still doesn’t work, there may be other issues. Consider consulting a professional or visiting a dealership for assistance.

Is it safe to replace the battery myself?

Yes, replacing the battery yourself is safe and straightforward. Just follow the steps outlined in this guide.

Additional Resources

For more information on changing key fob batteries for different makes and models, check out other videos and guides on fobbattery.com .

Thank you for reading this guide. I hope it helps you easily replace your Dodge Journey key fob battery.

Battery Replacement Guide for Dodge Journey Key Fob – Revive Your Remote’s Power

• Post author By phh-admin
• Post date 14.01.2024

When your Dodge Journey key fob starts to lose its battery power, it can be a frustrating experience. The key fob is an essential part of modern car technology, allowing you to remotely control various functions of your vehicle. Whether you need to lock or unlock the doors, open the trunk, or activate the panic alarm, a working key fob is crucial.

If you find that your Dodge Journey key fob is no longer functioning as it should, it’s likely time to replace the battery. Fortunately, replacing the battery for your Dodge Journey key fob is a relatively simple process that you can do at home. In this step-by-step guide, we will walk you through the process of replacing the battery and getting your key fob working like new again.

To replace the battery for your Dodge Journey key fob, you will need a small flathead screwdriver and a replacement battery. Start by locating the small slot on the edge of your key fob. Insert the screwdriver into the slot and gently pry apart the key fob to reveal the battery compartment.

Once you have opened the key fob, take note of the position of the old battery. Carefully remove the old battery and dispose of it properly. You may need to use the screwdriver to gently pry the battery out if it is stuck in place. Then, take your new battery and place it in the same position as the old battery, ensuring the positive side is facing up.

After replacing the battery, carefully reassemble the key fob by pressing the two halves together until you hear a click. Make sure that all the buttons are lined up correctly and that the key fob is securely sealed. Test the key fob by pressing the buttons to ensure it is working properly. If everything is functioning correctly, you can now use your freshly replaced battery for your Dodge Journey key fob.

Battery for Dodge Journey Remote Control

If the remote control for your Dodge Journey is not working properly, it may be time to replace the battery. The battery in the remote control fob is responsible for sending signals to your vehicle, allowing you to lock, unlock, and start your car. To ensure proper functioning of your remote control, it is important to replace the battery when it gets weak or dies.

The battery replacement process for a Dodge Journey remote control is simple and can be done in just a few steps. Here is a step-by-step guide to help you replace the battery in your Dodge Journey remote control:

• Locate the small groove on the back of the remote control fob.
• Using a small flathead screwdriver or a coin, carefully pry open the fob by sliding the tool into the groove and gently twisting.
• Once the fob is open, you will see the battery compartment.
• Remove the old battery from the compartment by gently pushing it out using your finger or a small flathead screwdriver.
• Insert a new CR2032 battery into the compartment, making sure it is facing the correct direction (usually with the positive side facing up).
• Close the fob by aligning the two halves and pressing them together until they snap into place.
• Test the remote control to ensure it is functioning properly by pressing the buttons to lock and unlock your vehicle. If the remote control is still not working, try replacing the battery again.

It is recommended to use a high-quality replacement battery to ensure optimal performance and longer lifespan. The battery for Dodge Journey remote control can be easily found at most electronic or automotive stores.

By following these simple steps, you can easily replace the battery in your Dodge Journey remote control and restore its functionality. Enjoy the convenience of a properly working remote control fob for your Dodge Journey!

Battery Replacement for Dodge Journey Key Fob

If your Dodge Journey key fob remote control is not working properly, it may be time to replace the battery. The key fob is an essential component for unlocking and locking your car, so a working battery is crucial.

To replace the battery for your Dodge Journey key fob, follow these steps:

Step 1: Find the Key Fob Battery

Locate the small slot on the side of your key fob. This slot is designed to open the key fob and access the battery. Use a small flathead screwdriver or a coin to pry open the slot. Once opened, you will see the battery compartment.

Step 2: Remove Old Battery

Carefully remove the old battery from the compartment. You may need a small tool to gently pop out the battery. Take note of the battery’s orientation and make sure to remember it when inserting the new battery.

Step 3: Insert New Battery

Take the new battery and insert it into the battery compartment. Ensure that the battery is aligned with the correct polarity, matching the orientation of the old battery you removed.

Step 4: Close the Key Fob

Once the new battery is securely in place, close the key fob by snapping the two halves back together. Make sure it is fully closed and there are no gaps.

That’s it! Your Dodge Journey key fob battery has been successfully replaced. Test the key fob by unlocking and locking your car to ensure it is working properly.

Remember to dispose of the old battery responsibly. Most key fob batteries can be recycled in designated battery recycling bins.

Key Fob Battery for Dodge Journey

If you’re experiencing issues with your Dodge Journey key fob, such as it not unlocking or locking your vehicle from a distance, it may be time for a battery replacement. The key fob is an essential remote device that allows you to control various functions of your Dodge Journey, such as locking and unlocking the doors, opening the trunk, and starting the engine.

The key fob for the Dodge Journey requires a small, round battery to function properly. Over time, the battery can become weak or die out completely, causing issues with the key fob’s performance. Fortunately, replacing the battery is a simple process that you can easily do yourself.

1. Gather the necessary tools:

You’ll need a small screwdriver, such as a flat-head or Phillips-head, and a new replacement battery. The battery type required for the Dodge Journey key fob is typically a CR2032.

2. Open the key fob:

Locate the small seam on the side of the key fob. Insert the screwdriver into the seam and gently twist or pry it open. Be careful not to apply too much force to avoid damaging the key fob.

3. Remove the old battery:

Once the key fob is open, you’ll see the battery compartment. Use the screwdriver to carefully remove the old battery from its slot. Take note of the battery’s orientation – ensure you install the new battery in the same way.

4. Insert the new battery:

Take the new replacement battery and place it into the battery compartment, ensuring it aligns with the correct polarity. Press down gently to secure the battery in place.

5. Close the key fob:

Align the two halves of the key fob and snap them back together. Apply gentle pressure until you hear a click, indicating that the key fob is securely closed.

Once you’ve completed these steps, your Dodge Journey key fob should be ready for use. Test it by pressing the buttons to ensure that it functions properly. If the issue persists, double-check the battery installation or consult a professional.

Remember to properly dispose of the old battery in accordance with local regulations. Regularly replacing the battery for your Dodge Journey key fob can help ensure its optimal performance and functionality.

Getting Started with Battery Replacement

If the key fob remote for your Dodge Journey is no longer working, it may be time to replace the battery. The key fob is an essential part of the vehicle’s remote control system, allowing you to lock, unlock, and start your car with ease. Fortunately, replacing the battery in your Dodge Journey key fob is a simple process that you can do yourself.

Before you begin, you will need a few key items:

• A replacement battery for your Dodge Journey key fob
• A small flathead screwdriver

Once you have these items ready, you can proceed with the battery replacement process. Here are the steps you need to follow:

Step 1: Open the Key Fob

Using the small flathead screwdriver, gently pry apart the two halves of the key fob. Be careful not to damage the plastic casing or any internal components.

Step 2: Remove the Old Battery

Locate the battery inside the key fob. It is usually a small, round disc. Use the screwdriver or your fingernail to carefully lift out the old battery.

Step 3: Insert the New Battery

Take the new battery and place it into the designated slot inside the key fob. Make sure it is inserted correctly, with the positive and negative sides facing the right way.

Put the two halves of the key fob back together, ensuring that they snap securely into place. Give the key fob a gentle squeeze to make sure it is closed properly.

Once you have completed these steps, your Dodge Journey key fob should be ready to use with its new battery. Test the remote control functions to ensure everything is working correctly. If the key fob still does not work, you may need to consult a professional for further assistance.

Gather the Necessary Tools

Before you begin the battery replacement process for your Dodge Journey key fob, make sure you have all the necessary tools on hand. Having these tools ready will ensure a smooth and hassle-free battery replacement experience.

Here’s a list of tools you’ll need:

By ensuring you have all these tools ready, you’ll be fully prepared to replace the battery in your Dodge Journey key fob without any delays or interruptions.

Locating the Battery Cover

Replacing the battery for your Dodge Journey key fob is a simple task that you can do yourself. Before you begin the battery replacement process, you need to locate the battery cover on your key fob.

The battery cover is typically located on the back of the key fob. It is a small rectangular or circular cover that is designed to protect the battery. To access the battery, you will need to remove this cover.

On some Dodge Journey key fobs, the battery cover may have a small indentation or a raised ridge. You can use your fingernail or a small flat-head screwdriver to gently pry open the cover. Be careful not to apply too much pressure, as you don’t want to damage the key fob or the battery cover.

Once the cover is open, you will see the battery inside. It is important to note the orientation of the battery before removing it, so you can insert the new battery correctly. Most Dodge Journey key fobs use a CR2032 lithium battery, but it is always best to check the owner’s manual for your specific key fob to confirm the correct replacement battery.

Now that you have located the battery cover, you can proceed to the next step of replacing the battery for your Dodge Journey key fob.

Removing the Battery Cover

To replace the battery for your Dodge Journey key fob, you will first need to remove the battery cover. Follow these simple steps to do so:

• Locate the battery cover. The battery cover for your key fob is usually located on the back of the fob. It is a small plastic cover that can be easily removed.
• Insert a small, flathead screwdriver. Gently insert a small, flathead screwdriver into the slot on the side of the battery cover.
• Pry open the battery cover. Use the screwdriver to pry open the battery cover. Apply gentle pressure and slowly lift the cover up until it pops off.
• Remove the battery cover completely. Once the cover is loose, remove it completely and set it aside.

With the battery cover removed, you can now proceed to replace the battery. It is important to note that the specific process may vary depending on the key fob model you have for your Dodge Journey. Refer to your vehicle’s owner’s manual or contact a certified Dodge technician for more detailed instructions.

Identifying the Battery Type

When it comes time for battery replacement on your Dodge Journey key fob, it’s important to know what type of battery to use. The key fob is the remote control for your vehicle, allowing you to lock and unlock the doors, as well as start the engine.

To identify the battery type for your Dodge Journey key fob, you will need to open the key fob itself. On the back of the key fob, you will find a small indentation or groove that you can insert a small, flat object into to pry it open.

Once the key fob is open, you will see the old battery. It is important to take note of the battery type and its orientation before removing it. The battery type is typically printed on the battery itself, or it may be listed in the key fob’s user manual.

Common battery types for Dodge Journey key fobs include CR2032 and CR2025. These are lithium coin cell batteries that are readily available at most electronics or automotive stores. It is important to use the correct battery type for replacement to ensure proper functioning of the key fob.

Note: When handling the battery, be sure to avoid touching the contacts with your fingers, as this can cause damage or reduce the battery’s lifespan. It is recommended to use gloves or a clean cloth when handling the battery.

Once you have identified the battery type, you can proceed with purchasing a replacement battery. Make sure to select a high-quality battery from a reputable brand to ensure optimal performance and longevity.

Now that you know how to identify the battery type for the Dodge Journey key fob, you can confidently proceed with the battery replacement process.

Removing the Old Battery

To begin the replacement process for the key fob battery in your Dodge Journey, you will need to remove the old battery. Follow these step-by-step instructions to complete this task:

• Locate the key fob that needs a battery replacement.
• Identify the battery compartment on the back of the key fob.
• Use a small flathead screwdriver or a coin to insert into the designated slot on the compartment cover.
• Gently twist the screwdriver or coin to open the battery compartment cover.
• Once the cover is removed, you will see the old battery inside the compartment.
• Take note of the battery’s orientation for proper placement of the new battery.
• Use a small tool, such as tweezers or the screwdriver, to carefully remove the old battery from its holder.
• Dispose of the old battery properly, following local regulations.
• Take the new battery, ensuring it is the correct type and size for your key fob.
• Insert the new battery into the holder, aligning it according to the orientation noted earlier.
• With gentle pressure, push the battery into place until it is secure.
• Replace the compartment cover by aligning it with the key fob and pressing firmly until it snaps into place.

Once you have completed these steps, your Dodge Journey key fob is now equipped with a fresh battery and ready to be used again for remote control access.

Inserting the New Battery

Once you have obtained a replacement battery for your Dodge Journey key fob remote control, it’s time to insert it. Make sure you have the correct type of battery for your specific key fob model.

1. Take the new battery out of its packaging and hold it by its edges. Be careful not to touch the battery terminals with your fingers as this may affect its performance.

2. Locate the battery compartment on your Dodge Journey key fob. The compartment is usually on the back of the key fob and can be opened by sliding a small lever or pressing a release button.

3. Open the battery compartment carefully. It may be hinged or may require you to remove a small cover plate.

4. Insert the new battery into the battery compartment with the correct orientation. Most key fobs will have markings or diagrams to show which side of the battery should face up.

5. Close the battery compartment securely. Make sure it is properly aligned and snaps into place. You may hear a click or feel a slight resistance when the compartment is closed correctly.

6. Test the new battery by pressing the buttons on your Dodge Journey key fob. If the buttons respond and the remote control functions as expected, the battery replacement was successful.

Remember to dispose of the old battery properly. Many retailers and recycling centers offer battery recycling programs to help protect the environment.

Ensuring Proper Battery Placement

When replacing the battery for your Dodge Journey key fob, it is important to ensure that the battery is properly placed. Incorrect battery placement can prevent the remote control from functioning properly, rendering it useless.

Start by locating the small slot on the edge of the remote control. Using a small flat-head screwdriver or a coin, gently pry open the key fob to expose the battery compartment.

Step 2: Identify the Battery Type

Take note of the type and size of the battery needed for your Dodge Journey key fob. It is typically a small lithium coin cell battery, such as CR2032. Make sure you have the correct battery before proceeding.

Step 3: Insert the Battery Correctly

Take the new battery and carefully insert it into the battery compartment of the key fob. Pay attention to the positive (+) and negative (-) markings on the battery and the corresponding symbols inside the compartment. Ensure that the positive side of the battery is facing up.

Gently press the key fob back together until it snaps shut. Make sure it is securely closed to prevent any accidental battery dislodgment.

By following these simple steps and ensuring proper battery placement, you can successfully replace the battery for your Dodge Journey key fob and ensure the remote control functions correctly.

Replacing the Battery Cover

When it comes time to replace the battery for your Dodge Journey key fob, you may also need to replace the battery cover. The battery cover is a small piece of plastic that protects the battery and keeps it secure in the fob. Here is a step-by-step guide on how to replace the battery cover.

Step 1: Gather the necessary tools

Before you begin, make sure you have all the tools you need. You will need a small screwdriver, such as a Phillips or flathead, to remove the screws that hold the battery cover in place.

Step 2: Open the key fob

Using the small screwdriver, carefully remove the screws on the back of the key fob. Once the screws are removed, gently pry open the key fob to access the battery and battery cover.

Step 3: Remove the old battery cover

Once the key fob is open, you will see the old battery cover. Carefully lift the cover away from the fob, taking care not to damage any of the internal components.

Step 4: Replace the battery cover

Take the new battery cover and align it with the slots on the key fob. Press down firmly to secure the cover in place.

Step 5: Close the key fob

Once the battery cover is replaced, carefully close the key fob. Make sure the buttons are aligned properly and press the two halves of the fob together until they click into place.

With the new battery cover in place, your Dodge Journey key fob is ready to use again. Make sure to test the fob to ensure it is working properly before you reassemble your keychain. If you have any issues with the replacement or need further assistance, consult your vehicle’s owner’s manual or contact a Dodge dealership for assistance.

Testing the Key Fob

Before completing the replacement of the battery for your Dodge Journey key fob, it is important to test the functionality of the key fob to ensure that the new battery is working properly.

To test the key fob, follow these steps:

• Stand near your Dodge Journey vehicle with the key fob in your hand.
• Press any of the buttons on the key fob, such as the lock or unlock button.
• Observe the response of the vehicle to the button press. The vehicle should lock or unlock, depending on the button you pressed.
• If the vehicle responds accordingly, the key fob is functioning properly. You can proceed with the battery replacement.
• If the vehicle does not respond or the response is weak, it is likely that the key fob battery needs to be replaced. Continue with the battery replacement process.

Testing the key fob ensures that the battery replacement will solve any issues with the key fob’s functionality. It is important to have a fully functioning key fob to ensure the convenient usage of your Dodge Journey remote keyless entry system.

Once you have confirmed the functionality of the key fob, you can proceed with the battery replacement process, following the step-by-step guide provided.

Following these steps will allow you to successfully replace the battery in your Dodge Journey key fob, ensuring that it continues to function properly for your remote keyless entry needs.

Troubleshooting Common Issues

While replacing the battery for your Dodge Journey key fob, you may encounter some common issues that can affect the functionality of the remote control. Here are a few troubleshooting tips to resolve these problems:

1. Key Fob Not Working After Battery Replacement

If your key fob is not working after the battery replacement, try the following steps:

• Ensure that you have inserted the new battery correctly, with the positive side facing up.
• Check if the battery has enough charge by testing it with a battery tester or using a multimeter to measure its voltage.
• If the battery is functioning properly, try reprogramming the key fob by checking the vehicle’s owner’s manual for specific instructions.
• If reprogramming doesn’t work, it may be necessary to contact a dealership or a professional locksmith for further assistance.

2. Key Fob Range Issues

If you are experiencing range issues with your key fob, where it doesn’t work from a sufficient distance, try the following:

• Replace the battery in the key fob, as a low battery can affect the range.
• Check for any obstructions that may be blocking the signal, such as metal objects or interference from other electronic devices.
• Try standing in different positions or locations to see if the range improves.
• If the range issues persist, it may be necessary to repair or replace the key fob.

3. Key Fob Buttons Not Responding

If the buttons on your key fob are not responding, follow these steps:

• Check if the battery is properly inserted and has enough charge.
• Inspect the buttons for any dirt, debris, or damage. Clean them if necessary and ensure they are not stuck.
• Try reprogramming the key fob, as a software glitch could be causing the unresponsiveness.
• If the buttons still do not respond, it may be a hardware issue, and you might need to replace the key fob.

By following these troubleshooting steps, you can address common issues that may arise during the battery replacement process for your Dodge Journey key fob. Remember, if you are unsure or unable to resolve the problems, it is always best to seek professional assistance.

Key Fob Not Working After Battery Replacement

After replacing the battery in your Dodge Journey key fob, you may find that it is not working as expected. Several factors could contribute to this issue, and it is important to troubleshoot to determine the underlying cause.

1. Battery Placement

Ensure that the new battery is placed correctly in the key fob. Double-check the positive (+) and negative (-) terminals and make sure they align properly with the corresponding markings inside the fob. Improper battery placement can prevent the key fob from functioning correctly.

2. Battery Quality

Consider the quality of the replacement battery. Opting for a low-quality or expired battery may not provide the necessary power to the key fob, resulting in malfunctioning. It is recommended to use a high-quality battery from a reputable brand.

3. Key Fob Synchronization

If the key fob is still not working after battery replacement, it might need to be reprogrammed or synchronized with your Dodge Journey. Consult the vehicle’s owner’s manual or contact a professional locksmith or dealership for guidance on how to synchronize the key fob to your vehicle’s system.

If all else fails, there might be an issue with the key fob itself. In such cases, it may be necessary to replace the key fob altogether. Consult a professional for further assistance in troubleshooting and resolving the issue.

Remember, the key fob is an essential component for controlling various features of your Dodge Journey remotely. Ensuring its proper functionality is crucial for a convenient and secure driving experience.

Key Fob Buttons Not Responding

If the buttons on your key fob are not responding, it can be frustrating and inconvenient. The key fob serves as a remote control for your Dodge vehicle, allowing you to lock and unlock the doors, open the trunk, and even start the engine.

There are a few possible reasons why your key fob buttons may not be working. One possibility is that the battery in the key fob needs to be replaced. Over time, the battery can lose its charge and will need to be replaced.

Check the Key Fob Battery

The first step in troubleshooting non-responsive key fob buttons is to check the battery. To do this, you will need to open the key fob. On most Dodge key fobs, there is a small slot that you can slide a small screwdriver or coin into to separate the key fob housing.

Once the key fob is open, carefully remove the old battery and replace it with a new one. Be sure to match the correct battery type and polarity. It’s a good idea to refer to the owner’s manual or consult a Dodge dealer for the correct battery replacement information.

If replacing the battery doesn’t solve the issue, there may be a problem with the key fob itself. It could be a damaged button, a loose connection, or a faulty circuit board. In these cases, it may be necessary to replace the entire key fob.

Key Fob Replacement

If you need to replace your key fob, there are a few options available. You can purchase a replacement key fob from a Dodge dealer or an authorized reseller. These key fobs will need to be programmed to work with your specific Dodge vehicle.

Another option is to purchase a replacement key fob online. There are many aftermarket options available that are compatible with Dodge vehicles. These key fobs may or may not require programming, so be sure to check the product description or consult the seller before making a purchase.

Once you have a replacement key fob, it will need to be programmed to work with your Dodge vehicle. This can usually be done by following the instructions provided with the key fob or by contacting a Dodge dealer for assistance.

In conclusion, if the buttons on your key fob are not responding, it’s likely due to a battery issue or a problem with the key fob itself. By replacing the battery or getting a replacement key fob, you can regain control of your Dodge vehicle’s remote functions.

Key Fob Battery Life Expectancy

The remote control key fob is an essential component for operating your Dodge Journey. It allows you to lock and unlock your vehicle, as well as start the engine remotely. Like any other electronic device, the battery in your key fob will eventually need to be replaced.

The average battery life expectancy for a Dodge Journey key fob is around two to three years. However, this can vary depending on usage and other factors. If you notice that your key fob is not working properly or the range is significantly reduced, it may be time to replace the battery.

Replacing the battery in your Dodge Journey key fob is a simple and straightforward process. Here are the steps to follow:

• Locate the small slot on the key fob and use a small flathead screwdriver or a coin to gently pry it open.
• Once the key fob is open, remove the old battery and replace it with a new one. Make sure to match the polarity markings on the battery and the key fob.
• Close the key fob by aligning the two halves and pressing them together firmly.

It is recommended to use a high-quality replacement battery to ensure optimal performance. Most Dodge Journey key fobs use a CR2032 battery, but it’s always a good idea to double-check the specifications in your vehicle’s owner’s manual.

By regularly replacing the battery in your Dodge Journey key fob, you can ensure that it continues to work reliably and efficiently. Remember to properly dispose of the old battery in accordance with local regulations.

With a new battery, your Dodge Journey key fob will be ready to use for another couple of years, providing you with convenient access and control over your vehicle.

Different Types of Key Fob Batteries

Key fobs are remote controls for your car that allow you to lock, unlock, and start your Dodge Journey. These key fobs are powered by small batteries, and over time, these batteries will need to be replaced to ensure optimal performance.

There are different types of batteries that can be used for Dodge Journey key fobs. The specific type of battery required will depend on the model and year of your vehicle. Here are some common types of key fob batteries:

• CR2032: This is one of the most common types of batteries used in key fobs. It is a small lithium button cell battery that provides a reliable power source for your remote control.
• CR2025: Another common battery type, the CR2025 is also a lithium button cell battery that is used in many key fobs. It provides a long-lasting power source for your remote.
• CR2016: This is another lithium button cell battery that is commonly used in key fobs. It provides a reliable power source and is often found in older models of Dodge Journey key fobs.

It is important to note that the specific battery type required for your Dodge Journey key fob may vary, so it is always best to consult your vehicle’s owner’s manual or a professional for the correct battery information. Additionally, when replacing the battery, make sure to use a fresh battery of the correct type, and follow the correct procedure to avoid damaging the key fob.

By knowing the different types of key fob batteries and how to replace them, you can ensure that your Dodge Journey key fob always has a reliable power source, allowing you to control your vehicle with ease.

Where to Purchase a Replacement Battery

When it comes time to replace the battery for your Dodge Journey key fob, there are a few options for purchasing a replacement. One option is to visit your local Dodge dealership. They will have the correct battery for your key fob and can help ensure that you get the right one.

Another option is to purchase a replacement battery online. There are many websites that specialize in selling replacement batteries for key fobs, including for Dodge Journey models. When buying online, make sure to double-check the compatibility with your specific key fob model.

In addition, you can also find replacement batteries for Dodge Journey key fobs at electronics stores, auto parts stores, and even some big-box retailers. These stores often carry a variety of battery options, making it easy to find the right one for your key fob.

Before purchasing a replacement battery, it’s a good idea to check the owner’s manual for your Dodge Journey or consult with a professional to ensure that you are getting the correct battery for your specific key fob model. This will help prevent any compatibility issues and ensure that your key fob continues to work properly.

Dodge Journey Key Fob Battery Specifications

The key fob for a Dodge Journey requires a specific type of battery to ensure proper functionality. The battery used in the key fob is a CR2032, which is a common coin cell battery. This battery is readily available at most electronics stores and online retailers.

When purchasing a replacement battery for your Dodge Journey key fob, be sure to look for a CR2032 battery. This battery is characterized by its 20mm diameter and 3.2mm height. It has a voltage of 3 volts, which is the standard voltage for most key fob batteries.

Replacing the battery in your Dodge Journey key fob is a simple process. First, locate the small slot on the edge of the key fob. Use a small flathead screwdriver or a coin to gently pry open the fob. Once the fob is open, you will see the battery compartment.

Remove the old battery by gently sliding it out of the compartment. Take note of the battery’s orientation, making sure to install the replacement battery in the same direction. Place the new CR2032 battery into the compartment, ensuring it is securely seated.

Once the new battery is in place, carefully close the key fob by aligning the two halves and pressing them together until they click into place. Test the key fob by pressing the buttons to ensure the new battery is working properly.

Remember to properly discard the old battery, as it contains hazardous materials. Many electronics stores and recycling centers have battery disposal programs to ensure safe and responsible disposal.

By following these specifications and steps, you can easily replace the battery in your Dodge Journey key fob and continue using the key fob to control your vehicle.

Preventing Battery Drain

To ensure that your remote key fob battery for your Dodge Journey lasts as long as possible after replacement, there are a few steps you can take to prevent unnecessary battery drain.

1. Keep the key fob away from other electronic devices: Electronic devices such as mobile phones, laptops, and tablets can interfere with the signal of the key fob, causing it to work harder and drain the battery more quickly. To avoid this, keep your key fob away from these devices when not in use.

2. Replace the battery as soon as it starts to weaken: If you notice that your key fob is not working as effectively as before, it may be a sign that the battery is starting to weaken. Replace the battery as soon as possible to prevent the key fob from working harder and draining the battery further.

3. Use the key fob sparingly: While the key fob offers convenience, using it excessively can drain the battery more quickly. When possible, use the physical key to enter and start your Dodge Journey to extend the battery life of the key fob.

4. Keep the key fob clean and dry: Moisture or dirt can cause the key fob to malfunction, leading to increased battery usage. Regularly clean your key fob and make sure it stays dry to prevent unnecessary battery drain.

By following these preventive measures, you can extend the battery life of your key fob for your Dodge Journey and avoid frequent battery replacement.

When to Replace the Key Fob Battery

The key fob is a remote control device that allows you to lock, unlock, and start your Dodge Journey. It relies on a small battery to function properly. Over time, the battery in the key fob will begin to weaken and eventually need replacement. There are a few signs to look out for that indicate it’s time to replace the key fob battery:

1. Decreased Range

If you notice that you have to be closer than usual to your Dodge Journey for the key fob to work, it’s likely that the battery is running low. As the battery weakens, the range of the key fob’s signal decreases. This can be an inconvenience, especially if you’re used to locking and unlocking your vehicle from a distance.

2. Unresponsive Buttons

When you press the buttons on the key fob, they should respond quickly and without hesitation. If you notice that the buttons are becoming less responsive or require multiple presses to function, it’s a strong indication that the battery is dying.

Don’t wait until your key fob stops working completely before replacing the battery. It’s best to be proactive and replace the battery as soon as you notice any of these signs. A key fob battery replacement is a simple and inexpensive fix that will ensure your key fob continues to work reliably for your Dodge Journey.

Other Key Fob Maintenance Tips

dodge Journey key fobs are not just about the battery replacement; there are other maintenance tips you should keep in mind to ensure the longevity and optimal performance of your remote control .

1. Clean the Key Fob: Regularly clean the key fob with a soft cloth to remove any dirt, dust, or debris that might accumulate on the surface. This will prevent any potential issues with the buttons or electronics.

2. Avoid Excessive Heat or Cold: Extreme temperatures can affect the battery life and overall functioning of the key fob. Avoid leaving it in direct sunlight or extreme cold to preserve its performance.

3. Replace Fob Case if Damaged: If the key fob case is cracked, broken, or damaged in any way, it is recommended to replace it. A damaged case can affect the key fob’s protection and may lead to malfunction.

4. Test the Range: Occasionally test the range of your key fob to ensure that it is functioning properly. Stand a reasonable distance away from your dodge Journey and test the functionality while pressing the buttons.

By following these other key fob maintenance tips, you can prolong the life of your dodge Journey key fob and ensure its reliable performance for years to come.

Consulting the User Manual

When it comes to replacing the battery for your Dodge Journey key fob, it’s always a good idea to consult the user manual for specific instructions. The user manual will provide you with the exact steps you need to follow in order to safely replace the battery in your remote key control. Here are a few reasons why consulting the user manual is important:

• Proper battery type: The user manual will specify the type of battery required for your Dodge Journey key fob. It’s important to use the correct battery type to ensure the remote control functions properly.
• Step-by-step instructions: The user manual will provide you with step-by-step instructions on how to replace the battery. By following these instructions, you can ensure that you’re taking the correct measures to replace the battery without causing any damage to the key fob.
• Precautions and safety: The user manual will also provide you with any precautions or safety measures you need to take while replacing the battery. This may include disconnecting the battery from the key fob or using protective gloves to prevent any electrical shocks.

By consulting the user manual, you can ensure a smooth and successful battery replacement for your Dodge Journey key fob. Be sure to locate the user manual for your specific Dodge Journey model to access the most accurate and relevant information.

Question and Answer:

What type of battery does the dodge journey key fob use.

The Dodge Journey key fob uses a CR2032 battery.

How do I open the Dodge Journey key fob to replace the battery?

To open the Dodge Journey key fob, you can use a small flat-head screwdriver to pry it open. Insert the screwdriver into the small gap between the two halves of the fob and gently separate them.

Where can I buy a replacement battery for my Dodge Journey key fob?

You can buy a replacement battery for your Dodge Journey key fob at most automotive parts stores, electronics stores, or online retailers. Some popular options include Amazon, Walmart, and AutoZone.

Do I need any special tools to replace the battery in my Dodge Journey key fob?

No, you do not need any special tools to replace the battery in your Dodge Journey key fob. All you need is a small flat-head screwdriver to open the fob and a new CR2032 battery to replace the old one.

How often do I need to replace the battery in my Dodge Journey key fob?

The battery in your Dodge Journey key fob may last for several years, but it is recommended to replace it every 2-3 years to ensure optimal performance. If you notice that the range of your remote control is decreasing or the buttons are not as responsive, it may be a sign that the battery needs to be replaced.

How often do I need to replace the battery for my Dodge Journey key fob?

The frequency of battery replacement for Dodge Journey key fob depends on various factors such as usage, battery quality, and environmental conditions. On average, the key fob battery may last 2-3 years. However, it is recommended to check the battery periodically and replace it when the key fob becomes less responsive.

What type of battery is required for a Dodge Journey key fob?

The Dodge Journey key fob requires a CR2032 lithium coin cell battery. Make sure to use the correct battery type for optimal performance. You can easily find this battery at most local convenience stores or automotive shops.

Can I replace the key fob battery for my Dodge Journey myself?

Yes, you can replace the key fob battery for your Dodge Journey yourself. It is a simple process that can be done in a few easy steps. However, if you are unsure or uncomfortable with performing the replacement yourself, it is recommended to consult your vehicle’s manual or visit a professional technician.

Related posts:

• Battery Replacement Guide for Dodge Key Fob – Keep Your Remote Working Perfectly!
• Battery Replacement Guide for Dodge Charger Key Fob to Keep Your Car Secure
• Battery Replacement for Your Dodge Journey – A Comprehensive Guide to Ensuring Optimal Performance and Reliability
• How to Replace the Battery in a Dodge Key Fob – Step-by-Step Guide
• How to Replace the Battery in Your Nissan Key Fob
• Signs It’s Time to Replace the Battery in Your Key Fob
• How to Replace the Battery in a Toyota Key Fob and Ensure Optimal Performance
• How to Replace the Battery in a Honda CRV Key Fob
• Where can I find the battery in a Dodge Journey?
• Battery Replacement for Honda Key Fob – Step-by-Step Guide to Restoring Your Key’s Functionality

Help us help you

Add your location so we can help connect you with local events and ticket offerings!

How To: Change a Key Fob Battery

Every vehicle on the market requires a bit of routine maintenance, even something as minor as switching the battery out of your key fob. If you’ve never had to do it before, here’s how:

If your vehicle came with a key fob that doesn’t need to be placed in the dashboard, here’s what you need to do:

• Step 1: Slide the lever on the back of the key fob to release the emergency key. Remove it and set it aside.
• Step 2: You’ll need some flat-sided object. A flathead screwdriver is your best bet!
• Step 3: Looking at the bottom of the fob and above where the emergency key spot was, you’ll see a blank slot. That’s where you want to insert your tool and gently pry the two halves of the key fob apart.
• Step 4: Separate the two pieces to reveal the inner electronics and the battery. Use the same tool to slide the battery out of its housing, paying attention to how it’s situated. If you forget, just look for the two “+” signs and match them up.
• Step 5: Grab the new battery, which is usually a CR2032 (can be found mostly at any auto parts store) and slide it into place.
• Step 6: Take the other half of the key fob and click the two portions back together; don’t forget to put your emergency key back in. And that’s it!

If you have an older vehicle that came with a key fob that needs to be placed in the dashboard, here’s what you need to do:

• Step 2: Flip the fob upside down so the buttons are facing away from you and the round end is facing upwards. There, you’ll see a tiny Phillips head screw, which you’ll need to remove next.
• Step 3: Once the screw is out of place, grab a flat-sided object. A flathead screwdriver is your best bet! Use it to separate the two halves of the key fob.
• Step 4: You should be able to see the inner piece of the fob. Simply lift it out and flip it over to get to the battery. Use the same tool to slide the battery out of its housing, paying attention to how it’s situated. If you forget, just look for the two “+” signs and match them up.
• Step 5: Put the new battery, which is usually a CR2032 (can be found mostly at any auto parts store) and slide it into place.
• Step 6: Put the three pieces back together and make sure they all fasten back into place. Put the screw and emergency key back into their places in the fob and then you’re done!

If you’re more of a visual learner, watch and follow along as SRTMush demonstrates:

Keep checking back for more how-to articles on DodgeGarage!

Home » Troubleshooting » Dodge Journey key fob not working – causes and how to fix it

Dodge Journey key fob not working – causes and how to fix it

The remote keyless system in Dodge Journey allows the driver to conveniently lock and unlock the vehicle with the press of a button. When the key fob stops working, it quickly becomes an inconvenience to manually lock and unlock the vehicle. In some cases it can even leave you stranded if the vehicle can’t detect the key and won’t let you start the engine.

The most common cause of key fob not working in Dodge Journey is dead battery. But the remote key can also stop working due to worn buttons, poor battery contact, water damage, defective key fob, receiver module issues, signal interference, dead 12 volt battery, and unpaired key requiring reprogramming.

1. Dead battery in key fob

Dead battery is the leading cause of key fob not working in Journey. Usually there are signs of weakening battery before it gives up. If the remote was working previously, but the range of the remote was gradually decreasing until it ceased to function, this indicates that the battery was wearing out.

Replace the battery

If the button cell battery in the key fob of Journey is replaced incorrectly or a battery is unsuitable, it can damage the vehicle key. Only replace drained batteries with new batteries in the same voltage, size, and specification. Make sure the battery is facing in the right direction when inserting it.

Recommended video

Key fob not working after replacing the battery

When purchasing a new battery for the key fob of your Journey, keep in mind that the battery may be sitting on the shelf for a long time. Therefore after replacement it may not work, or may not last that long. Try purchasing the battery from a store where stock moves fast. If you still can’t get the key fob to work after verifying that the battery is healthy, your key fob issues may not be due to bad battery.

Starting the engine with dead key fob battery

If your Journey has push button start/stop feature, your vehicle may not start due to weak key fob battery and a ‘key not detected’ alert message may be displayed in the instrument cluster. Don’t worry, you can still start your vehicle, the immobilizer is controlled by a passive transponder. Passive means, among other things, that the transponder in the key does not need its own power source.

Touch the start/stop button with your key fob and then start the engine. If it doesn’t work, then look in the owners manual for exact location of key fob placement, as it may vary depending on model.

Use spare key: You can try starting your Journey with its second key. It will also rule out any other problem with the first key, for example, water damage.

How long does the key fob battery last?

Depending on how often you use the key fob or remote control of your Journey, the battery should last between two and four years. This is assuming the new battery you installed is healthy and its use by date is many years away.

2. Poor battery connection

The battery inside the key fob of Journey has metal retaining clips that hold the battery in position and completes the circuit. If the clips don’t have any tension, it can cause contact issues and the remote may not receive any power. Make sure the battery is firmly placed and does not move around when you shake the remote. Also make sure all the battery contacts are corrosion and dust free.

3. Water damage

If your Dodge Journey key fob has taken a bath in the soapy water of the washing machine after you forgot to take it out of your pants pocket, water damage is very likely.

Water resistant, not waterproof

Your Journey key has rubber seals which prevents the water from getting to the electronic chip inside. A splash of water or brief exposure to light rain should be fine, but exposure to excessive amount of water like submerging the key in the pool can cause the water to penetrate the seals and damage the chip. Submerging the key in ocean water at the beach can be much more damaging to key fob electronics due to highly conductive nature of salt water.

But my key fob survived water exposure?

If your Journey key fob survived a wash cycle, or a deep bath in the ocean or pool water, it doesn’t make the key fob waterproof, it means you got lucky. Exposure to excessive water increases the risk of water damage, so you shouldn’t make this a habit.

What to do in case of water damage?

If your Journey key fob stopping working after exposure to clean tap water or rain, immediately remove the battery and clean the electronic component with paper towel and let it dry fully before putting back the battery. In case of exposure to salt water, or soapy or dirty water, it is recommended to clean the chip with isopropyl alcohol or electronic cleaner. If the key fob still doesn’t work after cleaning and drying, the chip is probably fried and you will have to buy a new key.

4. Dead 12 volt battery

The remote keyless system and the central locking system in Journey require the 12 volt battery to be in healthy state to function properly. If the 12 volt battery is dead or if the electric current has been interrupted due to corrosion on the battery terminals or the ground connection, all on-board electronics will stop working.

In this case, you will have to manually unlock the door of your Journey with physical key. Also, the electrical accessories (e.g. headlights, fan, and infotainment system) will not function or may function poorly, and the engine will not start. Check the 12v battery and its connections.

5. Signal interference

Journey remote control signal can be disrupted by objects, poor weather conditions or transmitters on the same frequency band close to the vehicle. The remote key may work when you’re near the vehicle, but may not work from a distance. In case of severe interference, the remote may not work at all.

Interference signals can be caused not only by neighboring radio masts and towers, but also by unprofessionally installed satellite systems. A large part of the radio interference is caused by defects and aging effects in electrical devices and radio systems, which lead to unwanted emissions, radiation and repercussions on power and communication networks. Your Journey key fob should start working again when you leave the area of interference.

6. Reprogramming required

In rare cases, the remote key of Journey may stop working due to pairing issues. The key can be reprogrammed with an OBDII scanner. You may also be able to program a key by following a few steps, an original key is typically required for successful pairing. The instructions should be mentioned in the owners manual. If you fail to do it yourself, you may have to visit an authorized dealer for reprogramming of the key.

7. Defective key fob

If your Journey key fob stopped working after you dropped it on the floor, you may have damaged the internal chip. Or, if your key fob just stopped working one day out of the blue, in rare cases this could indicate a faulty key fob – assuming you have tried everything to fix the issue e.g. battery replacement, reprogramming and the spare key fob works.

8. Faulty receiver module

Dodge Journey has a remote keyless system receiver that receives radio frequency signals from the key fob. If none of your key fobs work, and and you can’t reprogram the keys, it is possible the receiver module has developed a fault.

You may have to perform further diagnostics to identify the faulty. The keyless entry antenna could be damaged, or the module is just not communicating with other modules on the vehicle. In these cases an OBDII scan tool can be used to verify if the commands are being transmitted and acted on by the security module.

9. Electronic immobilizer fault

The immobilizer is an anti-theft security system that prevents the engine from being started and the vehicle from being moved with an unauthorized vehicle key. A fault in the immobilizer system can prevent your Journey from being started. You may also see a warning light with key symbol or key not detected message in the instrument cluster.

For vehicles with an ignition lock

There is a chip in the vehicle key. The chip automatically deactivates the immobilizer if a valid vehicle key is inserted into the ignition lock. The electronic immobilizer is activated automatically when the vehicle key is removed from the ignition lock.

For vehicles with a starter button

There is a chip in the vehicle key. It is used to automatically deactivate the electronic immobilizer when there is a valid remote control vehicle key in the vehicle interior. The electronic immobilizer is automatically activated as soon as there is no valid vehicle key in the vehicle.

The engine can only be started with a genuine vehicle key that is coded correctly. You can obtain coded vehicle keys from an authorized Dodge dealer.

Reset the system

If the key fob is not working due to a glitch in the keyless entry system, it may be possible to restore the functionality by resetting the keyless entry system in your Journey.

There isn’t any button or option to reset the keyless entry system in Journey, but you can reboot all the on-board computers by disconnecting the 12 volt battery for a few minutes. Remove the cable from the negative terminal of the battery first, then from the positive terminal. With the battery disconnected, press the horn button a few times and turn on the headlights to drain out all the residual electricity from the system. After about 15 minutes, reconnect the battery in reverse order: positive cable first, then negative cable.

Use OBD2 scanner for diagnosis

Since Dodge Journey is equipped with on-board diagnostics (OBD), a fault diagnosis can provide initial indications of where the malfunction is located. This method will be especially useful when diagnosing a faulty remote keyless system receiver module.

To begin troubleshooting, you must first connect the diagnostic tool to your Journey. The OBDII connector is usually located under the dashboard. With the tool connected, turn on the ignition. Most diagnostic devices then ask for some information about the vehicle. It is important that you enter this 100% correctly, otherwise the result of the search may be inaccurate. In addition to the vehicle make, model, and engine type, you usually also have to type in the Vehicle Identification Number (VIN). Since some OBD codes are manufacturer-specific, the scanner will be able to give you more accurate information if you enter more details about your Journey.

Conclusion:

There are many reasons why your Dodge Journey key fob is not working. When looking for the reason, you should start with the most obvious cause that is easy to diagnose: dead battery, which you can replace in a few minutes.

• Chrysler Sebring AC blowing hot air – causes and how to fix it
• Toyota Harrier won’t start – causes and how to fix it
• Cadillac CT6 AC smells bad – causes and diagnosis
• Buick Encore key fob won’t lock or unlock the doors
• Nissan Armada won’t start – causes and how to fix it
• Ford Everest AC not cooling – causes and diagnosis
• Chevy Silverado 1500 bad ignition coils symptoms, causes, and diagnosis
• Lexus RX AC blower motor not working – causes and diagnosis
• Honda Pilot heater not working – causes and diagnosis
• Nissan Maxima heater not working – causes and diagnosis
• VW Atlas Cross Sport Apple CarPlay not working – causes and how to fix it
• VW Transporter bad alternator symptoms, how to check voltage
• Dodge Viper steering wheel controls not working – causes and how to fix it
• VW Touran AC blowing hot air – causes and how to fix it
• Renault Kadjar AC not blowing hard enough – weak airflow causes
• Mercury Grand Marquis bad gas mileage causes and how to improve it
• Renault Kadjar AC smells bad – causes and diagnosis
• Chrysler Sebring bad O2 sensor symptoms, causes, and diagnosis
• Kia Carnival pulls to the left when driving
• Renault Scenic AC blower motor not working – causes and diagnosis