2011 dodge journey water pump replacement cost

Dodge Journey Engine Water Pump Replacement Costs

Our mobile mechanics bring the shop to you 7 days a week. get a quote today for your dodge journey.

Find Your Cost

AutoNation Mobile Service offers upfront and competitive pricing. The average cost for Dodge Journey Engine Water Pump Replacement is $495. Drop it off at our shop and pick it up a few hours later, or save time and have our Delivery mechanics come to you.

Why autonation mobile service.

We perform over 600 repair and maintenance services including oil changes, brakes, diagnostics, belts and hoses, and more. The best part? We come to you with all the necessary tools and parts.

How Much Does A Water Pump Replacement Cost?

Like any other replacement or repair, the total costs depend on your locality’s labor charges and the price of spare parts. 

You can expect to pay around $678 to $811 for a water pump replacement. This includes parts ($443 – $515 approximately) and labor costs ($234 – $296 approximately).

How Urgent Is A Water Pump Replacement?

As the water pump has the crucial job of cooling the engine, it’s best to get it repaired or replaced as soon as you spot an issue . 

Although your car may still run with minor water pump issues, it could damage other critical car parts like the engine if ignored for long. So get your car fixed by a professional to avoid expensive repairs and additional replacement costs.

When To Replace Your Water Pump

The water pump replacement cost should not deter you from considering the service. The pump prevents engine overheating by continuously circulating coolant from the radiator to the engine. As a result, a water pump malfunction is a serious issue as you’ll be looking at overheating, premature wear, and severe damage to vital car parts.

Here are a few signs to help you spot a water pump malfunction:

• High coolant temperature: The engine heats up without a good water pump, leading to high coolant temperatures. It’s usually indicated by an engine temperature warning light or elevated engine temperature reading on the dashboard.
• Radiator steam: Steam billows from the engine as the coolant can’t circulate in an overheated radiator when the water pump malfunctions.
• Abnormal noises: A loose accessory belt, pulley, or worn-out bearings in the water pump cause squealing and whining engine sounds, especially when accelerating.
• Fluid leaks: Green, orange (rusty coolant), or red-colored coolant may leak out when water pump components develop cracks or wear out. You can also check for frothy oil on the oil dipstick for possible internal leaks
• Fluctuating fluid gauge: If your temperature gauge needle oscillates between normal and high, your car’s water pump may be the culprit. A bad radiator or air bubbles can also cause inconsistent temperature readings.

3 Water Pump FAQs

Here are some of the most common queries about water pumps and water pump replacement cost, as well as their answers.

1. What Is A Water Pump?

A water pump is a mechanical impeller pump which is a device used to increase the pressure and flow of fluid.

You can find the water pump underneath the timing belt. That’s why experts advise replacing the water pump when you get your timing belt changed. 

The water pump plays a key role in your vehicle’s cooling system by circulating coolant from the engine to the radiator. This protects the engine and other essential parts from overheating. 

2. How Does The Water Pump Work?

When you start your engine, the fan belt and the water pump’s central axis also begin to turn — creating a centrifugal force. This force creates a suction that allows the pump to receive coolant from the radiator and send it to the engine.

The coolant absorbs the engine heat before it travels to the radiator, which cools the coolant again. 

Usually, the water pump can move around 7500 gallons every hour. However, the water pump adjusts its speed according to how fast the engine runs. It does so to absorb the heat that increases with engine speed — ensuring that the engine maintains normal temperatures.

3. How To Replace A Water Pump?

Each engine model may have its own belt drive system or water pump replacement steps. So it’s better to call an expert to help you replace or repair the water pump system.

Here’s how you can replace the water pump: 

• Disconnect the battery and wait until the engine cools down.
• Raise the car using a jack and jack stand. Place a fluid catch pan under your car before you remove the radiator cap.
• Proceed to drain the old coolant by lowering the radiator hose (safest method) or opening the radiator drain petcock.
• Use a ratchet or a wrench to loosen the water pump pulley retaining bolts . If the pulley starts to spin, put extra pressure on the belt tensioner to hold it in place.
• Next, rotate the automatic tensioner to remove the drive belt . If your vehicle has a manual drive belt tensioner, loosen the lock nut before turning the adjuster screw.
• Unscrew the water pump bolts and the pulley.
• Once done, remove the water pump slowly. If it doesn’t come off easily, tap the pump with a dead blow hammer.
• Remove water pump pulley retaining bolts . Then use brake cleaner to clean the water pump mating surface.
• After you mount the new gasket or seal in place on the water pump, install the new water pump and gasket .
• Reinstall the pulley bolts and tighten them after you fix the drive belt. 
• Finally, bleed the cooling system and refill it with coolant according to the manufacturer’s instructions. 
• Ensure your car engine doesn’t overheat by starting the engine and monitoring the temperature gauge.

Related repairs

Related dodge journey repairs.

Not sure? Let us diagnose

Other Repairs

We're here to keep you moving, our experienced mobile mechanics are ready to help..

1-Year | 12,000-Mile Warranty

• Remember me Not recommended on shared computers

Forgot your password?

• Maintenance & D.Y.I.

3.5L timing belt and water pump replacement

• timing belt

By JDennis February 5, 2018 in Maintenance & D.Y.I.

• Reply to this topic
• Start new topic

Recommended Posts

I haven't seen much in the way of more involved repair walkthroughs on forums for Journeys, so after replacing the timing belt and water pump on the wife's car I figured I'd write one to benefit others in the future. 

It is a significant savings to do this job yourself, and not terribly difficult if you've ever changed an alternator or other minor mechanical work. 

Background: The wife messaged me at work that the Journey was making a funny sound. I drove it and heard nothing. It would seemingly come and go at will. It turned out to the timing belt tensioner  had disintegrated. The internals were just floating around behind the timing cover . The front metal plate that at one time held the bearings was laying against the crank pulley when I opened it up, the rear plate was chewed up and mangled, and the bearings we're distributed at random throughout.

The job requires few specialty tools, which if you do not currently own, will potentially save you money down the road and, even if you must purchase them all at the time of the job, will still come out cheaper than paying a mechanic, or worse the dealership.

Job could take anywhere from a few hours for someone with experience to a full day, so set aside some time if this is your first time doing it. Apologies for the lengthy read, but I tried to be as descriptive as possible. Unfortunately I did not think to take photos while I was doing it.

What you need:

- Timing belt - Tensioner Pulley - Water Pump - Hydraulic Tensioner

Required tools:

- Harmonic Balancer Puller ($30 or so on Amazon) - E12 external torx socket (try to find as short of a socket as possible, there is not a lot of space to work) - T40 torx socket (again, shortest possible is better. Walmart used to carry a set made by Great Neck which were much shorter than any others I own. They're not great tools, but the bolt it will be used on does not require a lot of torque) - 10mm box wrench and socket - 13mm box wrench and socket - 15mm box wrench and socket - 16mm box wrench and socket - 18mm box wrench and socket - 24mm socket - 1/2" Impact wrench - 3/8" ratchet - Flathead screwdriver - Hammer - Pliers - Jack - Jackstands - small piece of wood (6" 2x4, 6" 1x4, small cube of plywood etc.) - shallow fluid catch pan

Optional tools ( but good to have):

- Slim head ratchet - Paint pen, nail polish, white out or other marking device that works on rubber, steel and aluminum. - Spring clamp

Start by parking on a flat level surface, with the vehicle in park, parking break set, and place wheel chocks in front and back of the rear wheels. 

Jack the vehicle up and place your jackstands. Check to make sure the jackstand feet are all touching the ground and that the vehicle is securely supported by them.

Remove the passenger wheel, and plastic belly pan if installed (Ours hasn't had the belly pan since we've owned it).

Lower your Jack and move it underneath the engine on the passenger side. Place your block of wood between the oil pan and the Jack and raise it until it is just touching the oil pan.

You can follow the recommended procedure for draining the coolant now, or... Just place your catch pan under the lower radiator hose and pull the lower hose off. 

While that is draining, remove the 2 13mm bolts holding the coolant reservoir in place, and the 1 13mm bolt holding the power steering reservoir. Lift the coolant reservoir and using your pliers, slide the clamps holding the lines back and remove the lines. Bend the lines out of the way and set the reservoir to the side. Thread the bolts back into their holes so they do not get misplaced.

Remove the 3 18mm bolts and 2 10mm bolts holding the upper right engine mount . Set it to the side and lay the bolts in the holes so they do not get misplaced.

Slide underneath the vehicle and remove the 2 long 18mm bolts holding the front lower center engine mount . Remove the rubber grommets, place them on the bolts and set the bolts in a location where they will not lost. You can remove the 4 or 5 bolts in the rear of the mount as well to allow more movement, but in my experience it wasn't necessary.

Using a 15mm box wrench lift the serpentine belt tensioner and remove the serpentine belt . Loosen the 15, or 16mm bolt that holds the tensioner arm in place. It only needs to come out enough to allow the alignment tab to be pulled out, and the tensioner arm pivoted up and down.

Remove the serpentine belt idler pulley.

Remove the 5 10mm bolts and 1 13mm bolt from the cast aluminum timing inspection cover. Place it to the side and lay the bolts in the holes so they do not get misplaced.

With your impact, remove the 18mm bolt securing the harmonic balancer to the crankshaft. Remove two of the small silver pivot bolts from your puller and attach the puller to the harmonic balancer. Slide the longer of the two rods into the puller bolt, grease the threads of the puller bolt, and thread it into the puller. Make sure the rod slides into the cavity on the crankshaft. Use a 24mm socket and your impact to remove the harmonic balancer. Set the harmonic balancer to the side and lubricate and thread the 18mm bolt back into the crankshaft. It only has to be flush with the crank gear and hand tight at this point, but you are going to be using it to turn the crank later.

From here in you will begin having to raise and lower the Jack supporting the engine periodically to create space to work.

Remove the 3 E12 external torx bolts from the power steering pump and slide it towards the front of the engine bay.

Remove the (I forget how many) 10mm bolts, use a deep 15mm socket or box wrench to remove the nut over the stud, and use your T40 socket to remove the one bolt that was behind the serpentine belt tensioner from the timing cover . 

Slide the timing cover over the stud and wiggle it out through the top. You may need to adjust the engine position to create space to get it out, be careful not to bend the cover.

With all of the timing belt components in place, rotate the crank shaft by hand until the arrow on the back of the crank pulley lines up with the arrow on the engine. Do not confuse the arrow on the back of the pulley with the notch on the face of the pulley. 

Check your cam gear to see if the lines on the cam gears line up with the marks on the bracket. If no lines are visible by the marks, look at the bottom of the pulleys, they are likely 180 degrees out. If that is the case, rotate the crank once more by hand until all marks line up.

At this point I like to use some brake cleaner and an air hose to clean everything up and blow any debris out. In my case the tensioner pulley had grenaded and the ball bearings as well as various other particles we're scattered throughout. Make sure you get everything cleaned out, so it doesn't end up damaging your new belt or components.

I also like to use a paint pen to clearly mark the timing marks so they are easy to identify.

Remove the 2 13mm bolts holding the tensioner in place and slide it towards the axleshaft and out of it's hole and discard. Remove the old timing belt and discard.

Place your new water pump face up  on a level surface. Remove (again, I forget how many) 10mm bolts securing the water pump. The bolts are two different lengths, so as you remove them from the old water pump, place them in the corresponding hole on the new water pump so you can keep track of where they go. 

Using a Flathead screwdriver and a hammer, gently tap the screwdriver under the face of the water pump and rotate it to pry the water pump free. Be careful not to mar the mounting surface on the engine. If you create a small bur, one the engine face you can use the hammer and screwdriver to tap it flat again, you just want the mounting surface to be clean, flat, and free from defects.

Place the old water pump next to the new one and transfer the bolts into their corresponding holes.

Check that the gasket for the new  water pump is firmly in place. Put the new water pump in place and finger tighten the bolts until they are snug. I could not find a specific order to tighten the bolts, but you want to jump around as you tighten them, criss crossing over the pump pulley. Do not start from one and go clockwise/counterclockwise. You want an even force to be applied so the gasket seals properly.

Remove the 15 or 16mm bolt holding the tensioner pulley to the tensioner arm. Install the new pulley.

Install the timing belt. Starting at the crank, I like to push a 1/4" ratchet handle to keep tension on the belt and pulley. Doesn't have to be wedged in hard, just enough to keep the teeth in place so they don't slip. 

Next slip the belt over the front pulley (right as you are facing it). You may have to rotate it clockwise slightly with an 18mm wrench when you slip the belt on and then push it counterclockwise to take up the slack. Just keep a controlled grip on the wrench and make slight adjustments. 

If you have some small spring clips you can use then here to keep the belt from sliding off of the cam gear or changing position, it doesn't have to be strong, in fact you want it to be a light grip to keep from damaging the cam gears which can be brittle, just enough to keep the teeth engaged.

When the belt is in place with slack taken up, slide it under the water pump pulley and over the rear (left as you are facing it) cam pulley. 

Slide the new hydraulic tensioner into place and lubricate and hand thread the bolts enough to get them started. You may need to adjust the grenade pin slightly, if it is pushed through and sticking out of the rear of the tensioner it will not be able to fit through the hole.

Slip the belt over the tensioner pulley and tighten the tensioner bolts just enough that you can still slide the belt off of the tensioner pulley .

Using a paint pen or other marking device, mark the cam pulleys and belt at a tooth location that will not be confused with the timing marks.

Tighten the tensioner bolts and check timing mark alignment. If anything has shifted, take note of how far off it is (1 tooth, 2teeth, etc)  slack the bolts and adjust belt position accordingly using the marks you made.

When the tensioner is firmly bolted in place and all marks line up correctly, remove the grenade pin. Check timing marks again. If they are not lined up, remove the tensioner and compress it using a vise or large c-clamp and reinstall the pin.

If all of your marks line up, place a 18mm wrench on the crank bolt and rotate the crank by hand for two full turns. Check your timing marks again. If they are off, remove the tensioner as described above and start over. If they line up correctly you are done.

Reassemble timing covers etc in reverse order. Refill coolant, purge air and the job is done.

I was unable to find torque specs specifically for the Journey, but did find some other vehicles that came with the 3.5L which had torque specs posted. 

I know there are some YouTube videos covering this procedure, but the videos tend to jump from step to step and I like having a written procedure to reference.

• JimBobLeNob

Link to comment

Share on other sites.

I'm on the fence about recommending OEM parts for the job. In all of my years working on cars I've never personally seen a tensioner pulley  come apart like that... 

I would however recommend purchasing quality parts from a reputable manufacturer at your own discretion, and purchasing all of the parts listed, as it is a time consuming job, a bit of a PITA because there's not much room to work, and you only want to do it once rather than keep going back to replace those parts you opted not to change.

Optionally you may wish to add cam and crank seals to your list. My wife's Journey was bone dry behind the timing cover , and I've never seen those seals leak enough to be of consequence. In my own experience, by the time they need replacing the engine  will likely be due for a rebuild or the scrapyard.

Left out coolant  as well, Zerex G-05

I'm surprised the the camshaft didnt skip and ruin a few valves in the process....guess you were lucky

Both cams were off one tooth. Timing belt  had two small vertical cuts on opposing ends about 10mm from the edge but otherwise in good condition. Tensioner outter ring was still riding on the inner, so maybe 8mm shorter? But the tensioner was now fully extended so maybe slightly less difference under no load or light load. Was enough to keep it going after failure, but if it went on any longer it'd be toast.

How many miles when this happened?  Sounds like a PIA job....

110k, it was due. Also swapped the fuel pump  module out today to fix the fuel level sending unit.

Messed with the original unit once I had it out to see why it quit working. The ground wire had an open... Was just insulation holding it to the terminal. They also didn't bother to actually strip any wire when they crimped the connectors on. 

Doesn't much surprise me since one of the coolant  fittings was only screwed in hand tight as well and backed out.

figure I'll rewire the old unit, solder the connections and keep it as a spare.

of note, the replacement module I got was molded differently. The alignment tab was slightly counterclockwise of where it should be, and the locking tabs for the plug we're not placed correctly.

being as I was already knee deep in it, I trimmed to fit and drove on.

car is check engine  light free again for the time being.

• 2late4u and larryl

• 9 months later...

Just finished this job up along with replacing all the motor and trans mounts. 

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account. Note: Your post will require moderator approval before it will be visible.

×   Pasted as rich text.    Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.    Display as a link instead

×   Your previous content has been restored.    Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

• Insert image from URL
• Submit Reply
• Existing user? Sign In

More Forum Apps

• Online Users
• Leaderboard

|| Forum Activity ||

• All Activity
• Create New...

CarParts.com will be back soon!

We apologize for the inconvenience. The CP Team is working on some upgrades to improve our service. Thank you for using CarParts.com!

You can call us at

1-866-529-0412

Reference ID: 18.8789ef50.1718102825.2e3577b

• Replacement Parts
• Engine Cooling & Climate Control
• Water Pumps

Enjoy fast, free delivery, exclusive deals, and award-winning movies & TV shows with Prime Try Prime and start saving today with fast, free delivery

Amazon Prime includes:

Fast, FREE Delivery is available to Prime members. To join, select "Try Amazon Prime and start saving today with Fast, FREE Delivery" below the Add to Cart button.

• Cardmembers earn 5% Back at Amazon.com with a Prime Credit Card.
• Unlimited Free Two-Day Delivery
• Streaming of thousands of movies and TV shows with limited ads on Prime Video.
• A Kindle book to borrow for free each month - with no due dates
• Listen to over 2 million songs and hundreds of playlists
• Unlimited photo storage with anywhere access

Important:  Your credit card will NOT be charged when you start your free trial or if you cancel during the trial period. If you're happy with Amazon Prime, do nothing. At the end of the free trial, your membership will automatically upgrade to a monthly membership.

Image Unavailable

• To view this video download Flash Player

AW6169 Water Pump & Gasket Fit for Dodge Challenger/Avenger/Charger/Durango/Grand Caravan/Journey, Chrysler 200/300/Town & Country, Grand Cherokee, Ram 1500/ ProMaster, VW Routan 3.6L V6 Engine

Purchase options and add-ons, about this item.

• 【Fitment】Compatible with Chrysler 200 2011-2014/ 300 2011-2022/ Town & Country 2011-2016, Dodge Challenger 2011-2022/ Charger 2011-2022/ Durango 2011-2015/ Avenger 2011-2014/ Grand Caravan 2011-2020/ Journey 2011-2019.
• 【Fitment】Compatible with Jeep Grand Cherokee 2011-2015, Ram 1500 2013-2018/ 1500 Classic 2019-2022/ C/V 2012-2015, ProMaster 1500 2014- 2021/ 2500 2014- 2021/ 3500 2014- 2021, Volkswagen Routan 2011-2014.
• 【Part Number】AW6169 1204450 120-4450 5184498AD 5184498AI 5184498AJ 5184498AK 5184498AL 5184498AM 5184498AE 5184498AH 68158680AB.
• 【Material】Made of high-quality aluminum material with good impact and wear resistance. And we are factory direct sales, enable you to have a better shopping experience.
• 【Package Includes】1 x AW6169 Water Pump, 1x Gasket. And easy to install!

Buy it with

Similar items that may deliver to you quickly

Product Description

AW6169 Water Pump Fit for the Following Vehicles:

Product information

Technical details, additional information, warranty & support, compare with similar items, looking for specific info, customer reviews.

Our goal is to make sure every review is trustworthy and useful. That's why we use both technology and human investigators to block fake reviews before customers ever see them.  Learn more

We block Amazon accounts that violate our community guidelines. We also block sellers who buy reviews and take legal actions against parties who provide these reviews.  Learn how to report

No customer reviews

• Amazon Newsletter
• About Amazon
• Accessibility
• Sustainability
• Press Center
• Investor Relations
• Amazon Devices
• Amazon Science
• Sell on Amazon
• Sell apps on Amazon
• Supply to Amazon
• Protect & Build Your Brand
• Become an Affiliate
• Become a Delivery Driver
• Start a Package Delivery Business
• Advertise Your Products
• Self-Publish with Us
• Become an Amazon Hub Partner
• › See More Ways to Make Money
• Amazon Visa
• Amazon Store Card
• Amazon Secured Card
• Amazon Business Card
• Shop with Points
• Credit Card Marketplace
• Reload Your Balance
• Amazon Currency Converter
• Your Account
• Your Orders
• Shipping Rates & Policies
• Amazon Prime
• Returns & Replacements
• Manage Your Content and Devices
• Recalls and Product Safety Alerts
• Conditions of Use
• Privacy Notice
• Consumer Health Data Privacy Disclosure
• Your Ads Privacy Choices

• About company
• GENERAL CONTRACTOR

+7 (495) 526-30-40 +7 (49657) 0-30-99

THE HISTORY OF THE COMPANY CREATION

1993 how the construction company remstroy was created   the year 1993 was a period when a lot of construction companies, which had been working successfully during the soviet times and had rich staff capacity, were forced to cease their activity for various reasons. a lot of capable specialists either had to look for another job or change their field. but there were also those who were willing to realise their potential in the field of construction in accordance with the received degree and the experience they had accumulated. thus, in 1993 in elektrostal (moscow oblast) a group of specialists and people sharing each other’s ideas, who had enormous educational background and the highest degree in architecture, organized and registered ooo firm erg which began its rapid development and successful work, offering its service both on the construction market and other areas. 2000 industrial construction is the main area   seven years of successful work have shown that combining different types of activities in the same company is not always convenient. and in the year 2000 the founders of ooo firm erg decided to create and register a monoprofile construction company ooo remstroy construction company. industrial construction was chosen as the priority area. it was in this area that the directors of ooo sk remstroy began their working life and grew as specialists. in order to achieve the set goal, they selected a mobile team of professionals in the field of industrial construction, which allows us to cope with the tasks assigned to ooo sk remstroy throughout russia and the near abroad. 2010 manufacturing of metal structures   we possess modern equipment that allows us to carry out the entire cycle of works on the manufacture of metal structures of any complexity without assistance. designing – production – installation of metal structures. a staff of professionals and well-coordinated interaction of the departments let us carry out the work as soon as possible and in accordance with all customer’s requirements.” extract from the list of members of self-regulatory organizations, construction.

LICENSE OF MINISTRY OF EMERGENCY SITUATIONS

Certificates, system of managing quality.

SYSTEM OF ECOLOGIAL MANAGEMENT

SYSTEM OF OCCUPATIONAL SAFETY AND HEALTH MANAGEMENT

LETTERS OF RECOMMENDATION

THE GEOGRAPHY OF CONSTRUCTION SITES

YOU CAN FIND MORE INFORMATION ON THE CONSTRUCTION SITES OF OOO REMSTROY ON THE PAGE OF THE SITE

OUR CLIENTS

http://remstroi.pro/yandex-promyshlennoe-stroitelstvo

Elektrostal

Elektrostal Localisation : Country Russia , Oblast Moscow Oblast . Available Information : Geographical coordinates , Population, Altitude, Area, Weather and Hotel . Nearby cities and villages : Noginsk , Pavlovsky Posad and Staraya Kupavna .

Information

Find all the information of Elektrostal or click on the section of your choice in the left menu.

• Update data

Elektrostal Demography

Information on the people and the population of Elektrostal.

Elektrostal Geography

Geographic Information regarding City of Elektrostal .

Elektrostal Distance

Distance (in kilometers) between Elektrostal and the biggest cities of Russia.

Elektrostal Map

Locate simply the city of Elektrostal through the card, map and satellite image of the city.

Elektrostal Nearby cities and villages

Elektrostal weather.

Weather forecast for the next coming days and current time of Elektrostal.

Elektrostal Sunrise and sunset

Find below the times of sunrise and sunset calculated 7 days to Elektrostal.

Elektrostal Hotel

Our team has selected for you a list of hotel in Elektrostal classified by value for money. Book your hotel room at the best price.

Elektrostal Nearby

Below is a list of activities and point of interest in Elektrostal and its surroundings.

Elektrostal Page

• Information /Russian-Federation--Moscow-Oblast--Elektrostal#info
• Demography /Russian-Federation--Moscow-Oblast--Elektrostal#demo
• Geography /Russian-Federation--Moscow-Oblast--Elektrostal#geo
• Distance /Russian-Federation--Moscow-Oblast--Elektrostal#dist1
• Map /Russian-Federation--Moscow-Oblast--Elektrostal#map
• Nearby cities and villages /Russian-Federation--Moscow-Oblast--Elektrostal#dist2
• Weather /Russian-Federation--Moscow-Oblast--Elektrostal#weather
• Sunrise and sunset /Russian-Federation--Moscow-Oblast--Elektrostal#sun
• Hotel /Russian-Federation--Moscow-Oblast--Elektrostal#hotel
• Nearby /Russian-Federation--Moscow-Oblast--Elektrostal#around
• Page /Russian-Federation--Moscow-Oblast--Elektrostal#page
• Terms of Use
• Copyright © 2024 DB-City - All rights reserved
• Change Ad Consent Do not sell my data